Results 1 to 4 of 4

Thread: Hand Brake Adjustment

  1. #1
    Member
    Join Date
    Jan 2017
    Location
    Coquitlam BC
    Posts
    56
    Thanks
    0
    Thanked 28 Times in 16 Posts

    Hand Brake Adjustment

    Just thought I'd share the procedure I used to tighten up my hand brake.
    After about 6 months use I found I had to pull the hand brake lever up too far to my liking
    to hold the car at a light or on a hill when parked.
    There is a procedure in the WSM but it does not tell you what size socket to use.
    The answer is you need a 10MM deep socket & short extension.
    I tightened mine to where it takes about 6 clicks upward before it starts to take hold.
    See the attached pictures to see where the wrench goes.


    Attached Images Attached Images   

  2. The Following 5 Users Say Thank You to jimwilly For This Useful Post:

    Daox (10-18-2017),LilGeckos (10-18-2017),MetroMPG (10-18-2017),MrMicra2015 (10-17-2017),ontario_micra (04-15-2019)

  3. #2
    Administrator MetroMPG's Avatar
    Join Date
    Feb 2014
    Location
    1000 Islands, Ontario
    Posts
    4,289
    Thanks
    1,376
    Thanked 547 Times in 422 Posts
    That's the easiest handbrake adjustment!

    Last time I did one, I'm sure I had to pull off the plastic junk around the lever, and adjust the 2 nuts on the ends of the brake cables.

    Thanks for sharing.

        __________________________________________

        click to view fuel log View my fuel log 2015 Micra S manual: 5.0 L/100 km ... 56.5 mpg (Imp) ... 20.0 km/L ... 47.0 mpg (US) ...


  4. #3
    Member
    Join Date
    Jan 2017
    Location
    Coquitlam BC
    Posts
    56
    Thanks
    0
    Thanked 28 Times in 16 Posts
    Your welcome.
    I got side-tracked by a picture I found online showing a turn buckle cable adjuster under the car (must be for an older Micra).
    I even rolled the rear tires up on ramps to look for the adjuster & found nothing but 2 shielded cables, one to each wheel.Name:  K13 Ebrake adjust.jpg
Views: 540
Size:  22.7 KB

  5. #4
    Junior Member
    Join Date
    Nov 2015
    Location
    windsor ontario
    Posts
    12
    Thanks
    0
    Thanked 6 Times in 4 Posts
    Quote Originally Posted by jimwilly View Post
    Your welcome.
    I got side-tracked by a picture I found online showing a turn buckle cable adjuster under the car (must be for an older Micra).
    I even rolled the rear tires up on ramps to look for the adjuster & found nothing but 2 shielded cables, one to each wheel.Name:  K13 Ebrake adjust.jpg
Views: 540
Size:  22.7 KB
    wow!!!! Thanks for the great tip. My car had rolled down the drive way yesterday. The brake was not engaging very tightly any more.
    I saw this tip for adjusting the parking brake. So I went to Canadian Tire and spent $6.00 for the deep 10mm socket.
    Stick it on the end of a speed handle (its nice and long) and in 1 minute the brake was adjusted.



  6. The Following User Says Thank You to skill57 For This Useful Post:

    MetroMPG (04-16-2019)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •