Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: Rear Diffuser Build

  1. #11
    Senior Member Azmodon's Avatar
    Join Date
    Jan 2015
    Location
    Niagara Falls Canada
    Posts
    190
    Thanks
    79
    Thanked 86 Times in 53 Posts
    it's on a very large list of things I have planned to complete before the first race, basically once the snows gone I'll be back with an update.


        __________________________________________

        click to view fuel log View my fuel log 2015 Micra SV automatic: 7.1 L/100 km ... 39.9 mpg (Imp) ... 14.1 km/L ... 33.3 mpg (US) ...


  2. #12
    Can we have some more of these thingys ?!?!lol holy look at em all
    Attached Images Attached Images   

        __________________________________________

        click to view fuel log View my fuel log 2015 Micra S manual: 7.7 L/100 km ... 36.8 mpg (Imp) ... 13.0 km/L ... 30.6 mpg (US) ...


  3. The Following User Says Thank You to IMPUL For This Useful Post:

    MetroMPG (01-18-2018)

  4. #13
    Senior Member Azmodon's Avatar
    Join Date
    Jan 2015
    Location
    Niagara Falls Canada
    Posts
    190
    Thanks
    79
    Thanked 86 Times in 53 Posts
    Might be overkill with an enclosed wheel :P but I'll be starting to print and mould the infinity wings for the splitter this weekend.

        __________________________________________

        click to view fuel log View my fuel log 2015 Micra SV automatic: 7.1 L/100 km ... 39.9 mpg (Imp) ... 14.1 km/L ... 33.3 mpg (US) ...


  5. #14
    Senior Member Azmodon's Avatar
    Join Date
    Jan 2015
    Location
    Niagara Falls Canada
    Posts
    190
    Thanks
    79
    Thanked 86 Times in 53 Posts
    Only six months late...

    I don't know how many clips are along the bottom, I don't care to count them since they're no longer on the car lol. The only thing holding the bumper on (as it's been for months) is the 2 bolts under the tail lights, the clips along the edge, and the flares. (also removed the bolt and nut at the termination point in the wheel well.

    So - removed lights, bumper, and foam thing:
    Name:  start.jpg
Views: 115
Size:  49.0 KB

    If you don't have an impact wrench, get to twisting... spare tire needs to come off and the cage removed - once removed you can unbolt the latching bracket for it near the rear of the car - there's also the hub mount for the spare hanging down in the middle:
    Name:  removed.jpg
Views: 113
Size:  37.8 KB

    Used a jack to mock up the location and measure for support rods - homedepot had a sale on 3/4" thick wall aluminum tubing... so summon your inner smith and get to banging
    Name:  hammered aluminum.jpg
Views: 113
Size:  44.4 KB

    There's a dimple in the middle of the rear end, being stiffer than the surroundings, that's the centre of the truss assembly - 1/4"-20 steel riv nut insterted
    Name:  rear point callout.jpg
Views: 117
Size:  36.9 KB

    For the front end, another dimple a few inches off centre was picked and drilled through in to the trunk and sealed with silicone - and the hub pad for the spare had its central hole enlarged to receive a 'PlusNut' (giant rivnut that can take ~2500 pounds) - 1/4-20 stainless steel rod and front mounting tube attached giving the front 2 points of contact - a third that's not pictured is from the remaining cage bracket right above the rear axle, gives the front two separate supports at 45 degrees to one another, and the threaded rod applies tension to both.
    Name:  front mount.jpg
Views: 112
Size:  37.3 KB

        __________________________________________

        click to view fuel log View my fuel log 2015 Micra SV automatic: 7.1 L/100 km ... 39.9 mpg (Imp) ... 14.1 km/L ... 33.3 mpg (US) ...


  6. #15
    Senior Member Azmodon's Avatar
    Join Date
    Jan 2015
    Location
    Niagara Falls Canada
    Posts
    190
    Thanks
    79
    Thanked 86 Times in 53 Posts
    The cage's front latch is in the shot below for clarity, it has a slot so it's more forgiving for positioning, you can also see the hole pre-enlargement:
    Name:  starting front.jpg
Views: 115
Size:  41.2 KB


    Moving back to the rear, a washer stack was used behind the second tube to bring it off the body panel, and 2 strips of neoprene (chemical / petroleum etc resistant) rubber were zip tied to the central pin and around each tube so movement doesn't cause tinking:
    Name:  mock up truss.jpg
Views: 122
Size:  47.1 KB
    Name:  truss start.jpg
Views: 115
Size:  40.9 KB

    The next step was balancing the unit on my chest while doing the worm to get under there. Had a friend install the two bolts at the truss while I mounted the front end - once it was up, it was still wobbling in the rear (truss only acts on a plane, need the third datum)

    A long time ago I had ordered two sets of splitter support rods from asia, they impressed me because the threaded ends are cut from the main rod, it's not a threaded rod inside a decorative casing, and the thing's some type of steel given they're ferritic. While I didn't end up needing them in the front, to my pleasant surprise they just so happen to be exactly the right length to reach from pre-drilled holes I made "just in case", and the windows in the crash bar.

    Name:  truss.jpg
Views: 110
Size:  52.8 KB

    So the smaller of the two made the rear end completely rigid. But after some leaf blower testing my cable support system wasn't stable - the main body prevents rotation on the Z, the cable prevents up and down flapping (rotation on the Y), but the winglette could still feather from 7 degrees to flat near the tips, speed dependent, as it rotated on the X... so the long rods run from 1.5" from the leading edge, to the middle mounting hole for the vents I printed... and tada 'dat booty doh'

    Name:  Finished.jpg
Views: 115
Size:  58.4 KB

    Kicking it feels stiffer than most body panels

        __________________________________________

        click to view fuel log View my fuel log 2015 Micra SV automatic: 7.1 L/100 km ... 39.9 mpg (Imp) ... 14.1 km/L ... 33.3 mpg (US) ...


  7. The Following 5 Users Say Thank You to Azmodon For This Useful Post:

    Daox (09-10-2018),MetroMPG (09-17-2018),MrMicra2015 (09-13-2018),Pete (09-11-2018),ptbo micra (09-11-2018)

  8. #16
    Moderator ptbo micra's Avatar
    Join Date
    Dec 2014
    Location
    Peterborough, ON
    Posts
    966
    Thanks
    397
    Thanked 322 Times in 220 Posts
    Hot damn! Will look good on the track at Tremblant!
    Get your MICRA-FORUM.com decal HERE!!

    Micra Meets: Loyalist Pkwy '15, '16 | Classique d'automne '15 '16 | Forks of the Credit '16 | Mosport '16

  9. #17
    Senior Member MrMicra2015's Avatar
    Join Date
    Aug 2016
    Location
    Vancouver BC
    Posts
    322
    Thanks
    58
    Thanked 45 Times in 32 Posts
    its unique and a feat of engineering....


    2015 Micra S (manual)
    no A/C /no power options
    Feb 2015 build
    9,999 purchase price + tax..no additional 1600$ because it was a 2015 purchased in 2016
    so receipt says $8,399....+1600 .... so they look good i guess...for a brand new car!

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •