Search:

Type: Posts; User: Gary

Search: Search took 0.01 seconds.

  1. DID you put a vacuum gauge on the intake manifold

    DID you put a vacuum gauge on the intake manifold
  2. The cable looks good but I need to shim it out....

    The cable looks good but I need to shim it out.
    [ATTACH]5938
  3. It is the rod cable it was not properly attached...

    It is the rod cable it was not properly attached to pedal see other thread
    Apologizing for p101 fault reply it was a weak fuel pump 100 used on ebay from Quebec. It has taken ages for the computer...
  4. Got a used fuel pump on ebay for 100 bucks from...

    Got a used fuel pump on ebay for 100 bucks from Quebec easy to put in under the back seat
  5. Mine was a weak fuel pump and it took forever to...

    Mine was a weak fuel pump and it took forever to get the computer to reprogram air fuel mix by driving it.
  6. I got 276k on mine and thinking about changing it...

    I got 276k on mine and thinking about changing it it still looks good and it is a pain to change
  7. Does it smell when you release it. It will start...

    Does it smell when you release it. It will start slipping in 5th gear on a hill my Volvo did and I changed it but it was rear wheel drive. Good luck changing it I read it is a 10 hr job. Do you...
  8. I found the problem the clutch cable attached to...

    I found the problem the clutch cable attached to the lever is not firmly attached it will slid right off which would leave me unable to release the clutch. I take it it pops over the ball on the...
  9. It is actually the clutch petal that has moved...

    It is actually the clutch petal that has moved lower at rest.I pulled it up and it works fine I just have to figure out how it is held in place.Good news is clutch is fine bad news is how to keep the...
  10. Thank You I have run out of travel the clutch is...

    Thank You I have run out of travel the clutch is barely released when the petal is on the floor.
  11. Thank You the parts dept says disc is different...

    Thank You the parts dept says disc is different plate and slave the same 900 for all 3 Amazon has a Versa one for about 230 cheap than Rockauro and good reviews.
  12. Clutch going way out of adjustment. SOLVED: cable end broken.

    I think I need a new clutch 276k on 2015
    Checked the brake fluid it is full
    It is getting hard to put in gear when pedal is fully depressed gets better as car warms up
    Does anyone know if it is...
  13. The purge valve solenoid is not working there is...

    The purge valve solenoid is not working there is 14.2 volts on the connector ordered one pickup tomorrow.Not sure if this will fix it.

    Thank You Gary
  14. ground wire

    Than You Rick
    I did check for Gnd at first
    I had a good gnd less than 1 ohm
    Battery voltage on 1 pin
    4.79 volts on another
    It ran terrible when MAF disconnected
    The versa manual has fault...
  15. P0101 fault code (Mass Air Flow sensor MAF?) SOLVED: plugged cat converter!

    2015 Micra with 239k
    I loose power on hills and get a 101 fault code
    Car runs fine on flat up to 100k
    New Mass air flow sensor no difference
    Vacuum gauge 19 inches at any RPM
    Accelerate to 5000...
  16. Replies
    2
    Views
    5,101

    2015 Micra gos into engine safe mode on highway

    I have a 2015 Micra standard tranny with 190k on it.I was driving down the highway at 90k and the car died coasted to a turn off and stopped.Restarted engine would not go above 2000 RPM.Limped home...
  17. Replies
    5
    Views
    10,384

    The onboard computer says I am getting 4.9 when...

    The onboard computer says I am getting 4.9 when I am getting 5.8 Speedo is off by about 8% odometer is close about 1%.I now have 90k on my 2015 Micra S love the car but the gears are way too short...
Results 1 to 17 of 17