Search:

Type: Posts; User: Azmodon

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Sound Proofing

    by Azmodon
    Replies
    13
    Views
    19,620

    I would advise against putting anything not...

    I would advise against putting anything not designed for the hood, on the hood. Most of the stuff I used is butyl rubber, which is really sticky, but when heated can lose some stick and catch fire...
  2. I mean... I'm looking at getting a new car soon...

    I mean... I'm looking at getting a new car soon anyway, I'd be down to risk it :P
  3. I've had the same issue (including death at a...

    I've had the same issue (including death at a stop), happens months apart. No codes, then about 2 months later an O2 code (one was dead and making me run rich) - replaced both, it's been less than a...
  4. Thread: Sound Proofing

    by Azmodon
    Replies
    13
    Views
    19,620

    I did, with the race exhaust it was quite loud...

    I did, with the race exhaust it was quite loud inside. I've since built a silencer to insert in the muffler, and it's really nice now but still keeps the growl. If I took the time to do it again, I...
  5. Replies
    21
    Views
    53,243

    No I mean mounting the radiator in the space...

    No I mean mounting the radiator in the space under the seat, it could span the seats mounting rails as they're only 10-14 inches long, 5-6 inches wide, 2-3 inches thick including fans. No foam...
  6. Replies
    21
    Views
    53,243

    ... I have no need to but... you could totally...

    ... I have no need to but... you could totally put a pc liquid cooling radiator with case fans under a seat, they're 12V and come with the pump and everything, just swap the hose barbs and add the...
  7. Replies
    5
    Views
    7,781

    I've been trying to figure out how to get one for...

    I've been trying to figure out how to get one for a while, no joy from instagram people in Mexico though due to covid. From wreckers there + shipping would be under 150 so... fingers crossed but...
  8. outside of a check engine light / Pcode, my first...

    outside of a check engine light / Pcode, my first question would be, have you swapped out any lights / checked for broken tail lights - I had both of my stock bulbs "break" but if I hit a bump the...
  9. Replies
    8
    Views
    7,664

    I'll be tearing apart the engine bay again this...

    I'll be tearing apart the engine bay again this week, will have to have a look, I would hope it's something like an inline resistor/fuse/choke etc. or something pertaining to the 'consult' system,...
  10. Replies
    7
    Views
    5,916

    30-50% rubbing alcohol is fine for the paint...

    30-50% rubbing alcohol is fine for the paint since the solvent isn't in contact for very long, do avoid using the 99% stuff straight, just water it down if that's all you have. Same goes for the head...
  11. Replies
    15
    Views
    25,706

    I don't think there's enough room at the front to...

    I don't think there's enough room at the front to reroute it... but you could fit an extra long tube muffler just after the cat and where it turns just before the gas tank, maybe transition to a...
  12. Replies
    15
    Views
    25,706

    I do custom designs on everything from carbide /...

    I do custom designs on everything from carbide / diamond cutting tools to architectural lighting, and restaurant cooking equipment. If you have an idea for something you want, even if it's just a...
  13. Replies
    3
    Views
    8,279

    Do you mean me? lol I'd actually defer to...

    Do you mean me? lol

    I'd actually defer to 514Xave (Post #16 from this page):
    https://micra-forum.com/showthread.php/2312-Custom-audio-box-sub-radio/page2

    I've only ever tied in with custom...
  14. Replies
    25
    Views
    38,655

    You'd also have like an inch less poke than I...

    You'd also have like an inch less poke than I did, so the worst case scenario would be detaching the 3-4 attachment points the liner has with the lip of the fender and either bending them up or...
  15. Replies
    25
    Views
    38,655

    I believe 7.5" is about as wide as you can go...

    I believe 7.5" is about as wide as you can go without poking a bit, +40 at that point would also bring the inside of the tire as close as you would want to your suspension (8" @ +40 I can't say for...
  16. If I've got time this weekend (and weather...

    If I've got time this weekend (and weather permitting) I'll remove the glove box and see what I can see. Since our cars are basically the Versa it should just be 8 screws, pull out the box, and then...
  17. I'm starting to see about a litre every 2K,...

    I'm starting to see about a litre every 2K, (threw in some restore just in case) had zero loss prior to 130K, need to do a full check but at least it's not leaking on to the ground any more lol
  18. I'm having the same issue but haven't even...

    I'm having the same issue but haven't even thought of bothering with it yet - louder music and road noise do their job :P if I get to it before you I'll let you know.
  19. Replies
    3
    Views
    4,078

    Take a wheel off, on the hub towards the rear of...

    Take a wheel off, on the hub towards the rear of the car you'll find the outer tie rod. The stub threaded in to it has the jam nut - loosen the jam nut. The inner tie rod has hex flats - twist the...
  20. There's a plastic tube on the other end of the...

    There's a plastic tube on the other end of the drain hole (attaches to the pan) they call the 'overflow tube'. So the volume of fluid below its upper lip is the volume they want in the device. But I...
  21. "requires mechanical competency" is mechanical...

    "requires mechanical competency"
    is mechanical engineering tech... k thx. The only tool I had was a fork... and I got it done. No panels were pulled, nothing was removed from the car but the...
  22. The procedure I had to follow was because I...

    The procedure I had to follow was because I didn't have a jack - as described. You can obviously access things under the car, from under the car. I was in a parking lot, on a mountain, 8 hours from...
  23. Replies
    5
    Views
    5,516

    dust shields behind the rotor are also notorious...

    dust shields behind the rotor are also notorious for rusting / sagging, making contact with brake bits. I had to bend mine back quite a bit because any time I hit a bump on of them made it sound like...
  24. Replies
    15
    Views
    25,706

    Oh I'll be there, won't know till Friday if I'm...

    Oh I'll be there, won't know till Friday if I'm going solo though
  25. Replies
    15
    Views
    25,706

    *theatrical DUN DUN DOOOONE!* Took all weekend...

    *theatrical DUN DUN DOOOONE!*

    Took all weekend to figure out the mounting... but I can put about 200Lbs on it without budging so... success.

    5450

    5451

    5452
Results 1 to 25 of 266
Page 1 of 11 1 2 3 4