Printable View
More to come..
Only raised rear by 3 3/8 inch.
Maid with 5/8 mdf so not too heavy. (36x21) 21 have too trim one place but really tight. probably better 20, 20 1/2 but have too fix it on frame...
I glue rear stock carpet on to look clean and cut trap for access....
I buy maestroRR sterring wheel control with interface. Pioneer 1330nex, all conector for stock harness (No cut)...
Nice build.
Thank's
Clean look, I like where you are storing the jack, and made use of the space where the jack was to keep a lower profile. Very nice job. Ive been considering doing something similar. Although your way take a little extra room, it is a much simpler approach to it then my idea.
May I suggest getting a mesh guard over your sub to protect it. I had mesh guards over my two 12” woofers in my pickup truck. They can handle a fair bit of weight put on top of them.
It's in my plan to protect the sub. Just buy a mesh for it or maybe put an other 12x12 mdf with carpet and raised up for sub clearence... (can put stock on top if i do this)
Looks great. I agree, I like the cargo area you incorporated.
aside from the amp... are those two massive LOC's or what?
it's 4 crossovers lol
nice idea with the storage
how did you run power wire???? to amp
have to wire all the car from crossover to speakers, pass 4 ga power ... i try to fish under carpet... Now i'm waiting for connector and dash kit.
New update ... Attachment 4328Attachment 4329Attachment 4330Attachment 4331
and in the car ...Attachment 4332Attachment 4333
its how you pass the power wire through the firewall (or other way?) i am most interested in.
i was able to easily "tuck" wire from passenger footwell to rear bumper without removing anything if that helps a bit (for a rearview camera)
PS
im not sure if the speaker acoustically is going to want the vented cover you put over it, you may want to try it without that, basically you put the speaker between 2 sealed boxes....:)
I probably pass wire this or maybe next weekend so i check best place ....
for rear camera and all other, have harness (cut nothing just plug and play and solder)
And for the sub i'm in the sealed spec for that sub (Pioneer TS-SWX2502 10” Loaded Shallow-Mount). i have the sealed box too and exactly the same if i put it face down. I see supose play best face down produce better sound... if not 6 screws and it remove lol
like this Attachment 4334
new Updates:
-APPS2Car Parking Brake Bypass Video
-Metra 70-7552 Radio Wiring Harness For Nissan 2007-Up
-Metra AX-NISUSB-2 USB Retention Harness 10-Up = Nissan FOR KEEP STOCK USB PORT
-Axxess AX-NIS32SWC-6V Backup Camera = Backup cam stock work with :)
-Metra Electronics 40-NI12 Antenna Cable = For radio
Maestro RR work for vol +,- for the rest have to swap 3 wired in Bluetooth module to confirm really work for mic and other steering wheel controle
Attachment 4343Attachment 4344Attachment 4345Attachment 4346Attachment 4347Attachment 4348
i find this plug right to hood cable(inside). outside it located in inner top plastic of the driver side wheel. Attachment 4367Attachment 4368
OMG i hope you found a passage from the engine bay to interior!!!!! let me know if it works.....
im a little fuzzy on where itis exactly......
for who ask me i post this maybe help for someone
The radio case is 7 inch and all the front is 8 or 7-15/16 inch
Attachment 4381Attachment 4384
Work fine for me... push the plug inside, make hole and put back....Attachment 4390Attachment 4391Attachment 4392
LOL im completely baffled, went out to look at my car and obviously i can see where the hood release goes through the fiewall, but there is so much padding im ASSUMING it goes through the firewall...tracing back from the hood latch, once it gets to the fender basically it "dissapears" under near the battery, so there is a huge maybe 3 foot "unknown lenght". i really appreciate the pictures, but i cant see exactly where you mean....maybe someone else can interprete??
OMG i found it!....on the outside at least, its a bit hard to see with the wheel on, but if you put your hand up you can FEEL the cable and the gromet
YOUR A GENIUS 514 !!!!!!!
- raised your car, remove the wheel (front driver), in front of the shock (top-right) by 6-8 inch here the cable and hole...
- in front of shock, the cable go in plastic fender. I fish here to where the pic i post now... if you don't understand lol hard to explain i try to take more pic tomorow...Attachment 4393
oooh and fish your wire (ext. to inside) of the car be gentle lol have many wired inside. take me 20 min to pass SOLO... hahaha
Attachment 4514Attachment 4515Attachment 4516Attachment 4517Attachment 4518
Phase 1: custom speaker mount/speaker/crossover/tweeter INSTALL. play on radio not amp. DONE
phase 2 : have to pass wire, (amp to crossover) next time
514 awesome job...forgive me but.... what are the rectangular "boxes" with he red circles sort of semi attached to the inside of the doors ?????
you dont have a template drawing for those speaker adapters do you ? bolt circle?...been looking online for ages...should be standard nissan
how come it looks like you have 3 different adapters??...a bought one and a homemeade one and a homemade painted one ?
the rectangular box is the crossover for speaker and tweeter.
the nissan speaker is 1 1/4 height so i use the two layer of (mdf 5/8).
i use stock speaker for bottom piece (all 4 is the same) and i have bracket come with speaker to attach grill on it. I just use it to cut second mdf. (2) 6 1/2 front and rear is (2) 5 1/4.
i glue and screw it ... oh and i use dremel to cut my pieces. not the best clean cut ever but it made the job
aaah....didnt see the tweeters you mounted in the doors. makes sens now..
no problems putting the "box " in the doors in regards to space or door panel not fitting ?
No have place ..... :) my crossover are not small too (6 X 4 X 1)inch
only have to remove cap inside door panel. front is just clip and rear have 3 screws.