I mean... I'm looking at getting a new car soon anyway, I'd be down to risk it :P
I mean... I'm looking at getting a new car soon anyway, I'd be down to risk it :P
I did, with the race exhaust it was quite loud inside. I've since built a silencer to insert in the muffler, and it's really nice now but still keeps the growl. If I took the time to do it again, I...
No I mean mounting the radiator in the space under the seat, it could span the seats mounting rails as they're only 10-14 inches long, 5-6 inches wide, 2-3 inches thick including fans. No foam...
... I have no need to but... you could totally put a pc liquid cooling radiator with case fans under a seat, they're 12V and come with the pump and everything, just swap the hose barbs and add the...
I'll be tearing apart the engine bay again this week, will have to have a look, I would hope it's something like an inline resistor/fuse/choke etc. or something pertaining to the 'consult' system,...
You'd also have like an inch less poke than I did, so the worst case scenario would be detaching the 3-4 attachment points the liner has with the lip of the fender and either bending them up or...
I believe 7.5" is about as wide as you can go without poking a bit, +40 at that point would also bring the inside of the tire as close as you would want to your suspension (8" @ +40 I can't say for...
If I've got time this weekend (and weather permitting) I'll remove the glove box and see what I can see. Since our cars are basically the Versa it should just be 8 screws, pull out the box, and then...
Oh I'll be there, won't know till Friday if I'm going solo though
*theatrical DUN DUN DOOOONE!*
Took all weekend to figure out the mounting... but I can put about 200Lbs on it without budging so... success.
5450
5451
5452
had to get up at 5:30 and drive 2 hours in to the heart of Toronto... couldn't sleep I was so excited... now the fun part.
5438
5439
5440
I have my demon eyes running through the provided grommet, drilled another hole beside it and have a cable gland securing the power line for the subwoofer. The wires come in above and to the left of...
They're all pretty much the same, I have a K&N one on right now, have had Injen prior... as far as I can tell they're all the same material.
constructively... swap your transmission? Math is math... in top gear with a stock transmission, it must rotate (and thus your engine must turn) a certain number of times per revolution of your...
You can go through my garage for a semi up to date list of mods, but as far as issues go I've only had 2, the most recent being the driver side door... plastic, keepy open thing... I have no idea...
tipped the mirror so it was facing as far away from the car as possible - grabbed the inside lip and with gentle tugs it let go
5213
5214
5215
5216
Had been hearing the door make a light click when closing from fully open for a few months now... since I couldn't see the hinge when it happened I couldn't really identify where it was coming from....
The Cd of a mirage is 0.27, the micra is 0.32, so that's going to hurt, the mirage is also 500Lbs lighter, so once up to speed it'll cruise will less input.
The radiator on our cars were designed...
In regards to the first oil change, running at least 1000km is usually beneficial prior to the first change, but it's more so the filter that you'd be worrying about, the oil itself is fine... do...
I followed the chrysler model for break in, given it was a non-test driven car when I got it. Their white papers don't care much about seals and seats, but properly case hardening surfaces. So it's...
Note to self: always remember the full scale prototype... enter Mk5
5147
5148
and... when you finally get your new company logo, why not include it?
5149
and what it might look like installed
5140
5141
5142
It's bolted in to the chair, so the only way to move it would be to get in there and adjust the bracket -> alternatively, you could fashion a padded arm rest cover that zips around the whole thing...
The Flex Z for the Nismo is the set to get if you're doing coilovers - a few of us prior to knowing that got the "street advance" series for the standard K13 -> which doesn't have the front sway bar...
So first we ran out of gas, then we got gas but the welder was booked, then we ran out of wire - Finally back in action.
Since the cat's a bit more critical I "tested" the settings I'll need to...